rdharvey Posted September 3, 2010 Share Posted September 3, 2010 Our new 2011 software has now been installed and set up although our previous template does not come through and it seems to have disappeared from the 2010 templates folder... any ideas where else it could have located itself:? and if it would just be easier to re create a new template? if so how do you start with a blank page to there on sketch your templates? thanks Quote Link to comment Share on other sites More sharing options...
stevsmith Posted September 3, 2010 Share Posted September 3, 2010 Open an new drawing and in the model tree you will find a folder called drawing resources. Maximise this folder and then maximise the title block folder, Right click on ISO (or whatever is default) and click edit. This will take you into the title block editor. Do what you have to do. Note in the text properties you can input model parameters and such as required. Click finish sketch when done and save. Before you shut down the drawing goto the big yellow I and save as template, this will take you directly to your template folder and save under whatever you choose. Quote Link to comment Share on other sites More sharing options...
Dana W Posted September 3, 2010 Share Posted September 3, 2010 Use the most recent drawing that was made from the 2010 template as a resource. It should have most of the title block/border and 'styles' stored in it. Quote Link to comment Share on other sites More sharing options...
rdharvey Posted September 3, 2010 Author Share Posted September 3, 2010 yeah thats what i have done. thanks guys. Quote Link to comment Share on other sites More sharing options...
Dana W Posted September 3, 2010 Share Posted September 3, 2010 yeah thats what i have done. thanks guys. Already? Wow. Quote Link to comment Share on other sites More sharing options...
JD Mather Posted September 3, 2010 Share Posted September 3, 2010 Probably obvious now, but for future reference you should always have a backup of your company template in a secure, known location before upgrading software versions. Quote Link to comment Share on other sites More sharing options...
rdharvey Posted September 3, 2010 Author Share Posted September 3, 2010 Yeah all the little things i know i should have tried clicked in once the first bit of advice was given. As for the software it was changed whilst i was on holiday which was a little unfortunate i suppose! Makes it even worse as obviously they have changed all the log in details etc and it made a bit of an issue with file paths but i seem to have that sorted now! Opps just realised im in caps :/ sorrryy Quote Link to comment Share on other sites More sharing options...
rdharvey Posted September 3, 2010 Author Share Posted September 3, 2010 Already? Wow. haha! Man on a mission!! Quote Link to comment Share on other sites More sharing options...
max2017 Posted September 3, 2010 Share Posted September 3, 2010 I was looking for it for some time jejeje thank you! Quote Link to comment Share on other sites More sharing options...
CAnnondale Posted September 7, 2010 Share Posted September 7, 2010 Hi, I have question. How to change the orientation of the border/block from landscape to portrait. Quote Link to comment Share on other sites More sharing options...
czc Posted September 7, 2010 Share Posted September 7, 2010 Right click your sheet and select edit sheet. There is a section called orientation. Quote Link to comment Share on other sites More sharing options...
CAnnondale Posted September 8, 2010 Share Posted September 8, 2010 Right click your sheet and select edit sheet. There is a section called orientation. Thank you very much. Quote Link to comment Share on other sites More sharing options...
Dana W Posted September 8, 2010 Share Posted September 8, 2010 Hi, I have question. How to change the orientation of the border/block from landscape to portrait. Start a new thread with a new question. Quote Link to comment Share on other sites More sharing options...
rdharvey Posted September 20, 2010 Author Share Posted September 20, 2010 its in the page settings.. Quote Link to comment Share on other sites More sharing options...
Dana W Posted September 20, 2010 Share Posted September 20, 2010 Start a new thread with a new question. An Apology here. I should have kept my mouth under my hat. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.