numberOCD Posted February 28, 2012 Share Posted February 28, 2012 Hi, I'm trying to show a band stretch in Studio and am not sure how to do it. I am not concerned about the band getting thinner to maintain volume, just the elongation along the x-axis. Any ideas? Thanks Quote Link to comment Share on other sites More sharing options...
JD Mather Posted February 28, 2012 Share Posted February 28, 2012 Create the band with a parameter for the straight length (I assume center-to-center distance). Animate Parameter in studio (change the length longer or shorter). So it is really a fudge - not really stretching but changing the actual length to represent stretching. Quote Link to comment Share on other sites More sharing options...
numberOCD Posted February 28, 2012 Author Share Posted February 28, 2012 Thanks again. I'll test that in the morning (hopefully) once I finish the animation with the cranes. I also meant to ask, am I able to suppress constraints during the animation so they have no effect after or before a given time range? Quote Link to comment Share on other sites More sharing options...
numberOCD Posted February 29, 2012 Author Share Posted February 29, 2012 Sorry, this is kinda dumb; I can't figure out how to get the parameter accessible in the assembly. What do I need to do to make the parameter adjustable in the assembly? Quote Link to comment Share on other sites More sharing options...
JD Mather Posted March 1, 2012 Share Posted March 1, 2012 Add to Favorites. I think this is covered in one of the Tutorials. Quote Link to comment Share on other sites More sharing options...
numberOCD Posted March 9, 2012 Author Share Posted March 9, 2012 Sorry, but I'm still lost on how to get the parameter of a part into the favorites of the assembly. Could you give me quick guide on that transition? It's been digging into my nerve for the past week. Thanks for all the help! Quote Link to comment Share on other sites More sharing options...
JD Mather Posted March 9, 2012 Share Posted March 9, 2012 Attach your assembly here. Quote Link to comment Share on other sites More sharing options...
numberOCD Posted March 9, 2012 Author Share Posted March 9, 2012 The file I have is too large, so let me work up a quick one of just a piece for expansion Quote Link to comment Share on other sites More sharing options...
numberOCD Posted March 9, 2012 Author Share Posted March 9, 2012 ArrowDemo.ipt The "Arrow Extender" Parameter is the parameter. If you can show me how to animate it when placed in an assembly, that's what i'm looking for. Thanks again! Quote Link to comment Share on other sites More sharing options...
numberOCD Posted March 12, 2012 Author Share Posted March 12, 2012 I'm stuck again with stretching the parameters in animation. I got the favorite parameter assigned to the PulleyCable parameter and it animated fine when it had no constraints. But once I secured on end to the pulley wheels it got stuck and will not operate now. I'm trying to use the parameter to move the hook assembly, just as if it were the cable operating it. Could anybody tell me how to allow the parameter to animate with a constraint still applied? Thanks! CranePart2.zip CranePart 5.zip CraneMainAssembly.zip CranePart3.zip CranePart4.zip CranePart1.zip Quote Link to comment Share on other sites More sharing options...
JD Mather Posted March 12, 2012 Share Posted March 12, 2012 I opened the PullyCable2 part and noticed that Sketch1 is not fully constrained (defined). Missing tangent constraints and one dimension and a duplicated dimension. You might start by reading this document http://home.pct.edu/~jmather/skillsusa%20university.pdf Quote Link to comment Share on other sites More sharing options...
numberOCD Posted March 13, 2012 Author Share Posted March 13, 2012 So if I want it to stretch evenly on both sides should I animate both dimensions or leave on dimensionless? Quote Link to comment Share on other sites More sharing options...
numberOCD Posted March 13, 2012 Author Share Posted March 13, 2012 Ok, I constrained it as you noted and had only one vertical dimension with the opposite as just a following line. When I applied the parameter to favorites in the ipt and then to an iam I placed it in for a demonstration it works perfectly. But when I put it into the CraneTop file from yesterday (and I have removed and replaced the pulley cable more than 5 times), it works ONLY when no constraints are holding it to the pulley wheels. The moment I constraint to stationary end of the parameter, it fails to operate, but ONLY in my existing files. I can get it to move the second pulley wheel in my demonstration file. Why is this error occurring only in certain files? If I have placed the same file with a favorite parameter multiple times in the same assembly does this cause a problem? I noticed that when I installed the CraneTop assembly a second time in the overall plans and referenced the parameter, it seemed to still refer to only on parameter; are every instance of the pulley cable's parameter synced? I am stressed for time and cutting corners on this part but badly need the parameters to animate with constraints on another item later today. Thanks again for all your help. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.