+ Post New Thread
Page 1 of 11 1 2 3 ... LastLast
Threads 1 to 25 of 253

Forum: Student Project Questions

If you're a student learning AutoCAD and are following a course of study such as those at Penn Foster, you can get help with your project work by posting here.

  1. -Penn Foster? HVAC transition piece

    Hello! Does Any One Know How To Draft A 10"x14"x6" RECTANGULAR Hvac Pattern THATS 14"X6" ON ONE SIDE AND10"X6" ON THE OTHER

    Started by drafterjohn773‎, 15th Nov 2009 02:40 am
    6 Pages
    1 2 3 ... 6
    • Replies: 55
    • Views: 8,769
    Yesterday 09:47 pm Go to last post
  2. Penn Foster Structural Elective

    hello, i have completed everything thus far in this project, but i am lost with the elective, i have another week to finish so i can go to school in the fall (sponsored by work safe because of an...

    Started by coreyjaywilliams‎, 12th Aug 2013 06:52 pm
    6 Pages
    1 2 3 ... 6
    • Replies: 53
    • Views: 6,189
    18th Sep 2015 10:06 pm Go to last post
  3. Penn-foster electrical grade report

    HELLO EVERYONE, Got a 100 on the electrical project. post screen shots. I have submitted the Civil and Elective Electrical. finally finished the course. my average is now a 92. now we wait to see...

    Started by Hondatek‎, 2nd Jun 2015 06:26 am
    • Replies: 2
    • Views: 589
    17th Sep 2015 06:27 pm Go to last post
  4. Angry Penn Foster Drafting with AutoCad Structural help with the rebar.

    Guys, I am having trouble picturing how this should look like. Page 11 in the book. The rebar in the bottom of the footings is #6 rebar at 8 OC both ways. The callout for the rebar is as...

    Started by Hondatek‎, 15th Jan 2015 06:15 am
    8 Pages
    1 2 3 ... 8
    • Replies: 78
    • Views: 5,039
    17th Sep 2015 01:05 am Go to last post
  5. Penn Foster Student Suffering with Oleson Village Map!!!

    I see lots of posts on this project but I'm getting no where. I completed all of the book tests and got no less than a 95 on every single one but when it came time to do the project at the end, it...

    Started by AutoCad Student‎, 5th Dec 2012 11:28 am
    25 Pages
    1 2 3 ... 25
    • Replies: 249
    • Views: 31,577
    15th Sep 2015 11:51 am Go to last post
  6. Unhappy How do I approach this? - 3D Ergonomic Cup

    I have designed the Cup part, however I'm having a hard time on how to approach the handle part of it. I plan to design it in 2D and then use revolve, but I'm stuck on the 2D part... How do I make...

    Started by infernowheels‎, 21st Aug 2015 01:07 pm
    • Replies: 4
    • Views: 396
    22nd Aug 2015 04:12 pm Go to last post
  7. Embarrassed One Point Perspective

    Hey guys, Okay I am a bit confused, thought I had this down, but the more I look into it the more confused I get. The book I am using has about 4 paragraphs on how to do this, and it leaves out...

    Started by Behemothrex‎, 5th Aug 2015 11:01 pm
    • Replies: 5
    • Views: 628
    6th Aug 2015 04:25 pm Go to last post
  8. Angry Teeth on a curve?

    Hey Guys, Once again my class is asking me to draw something I never have, with zero instruction. Did I mention the textbook has zero drawing instruction in it LOL. So I am drawing this part...

    Started by Behemothrex‎, 30th Jul 2015 02:57 am
    • Replies: 6
    • Views: 584
    5th Aug 2015 10:19 pm Go to last post
  9. Exclamation Oleson village notation

    I know I saw it in one of the threads, but I can't find it again now that I need it. How do I get the degree symbol when I'm putting in the bearing text? For example, N87(degrees)W?

    Started by Legacy14‎, 27th Jul 2015 05:14 pm
    bearings, degrees, oleson village, project 4, text notation
    • Replies: 3
    • Views: 446
    4th Aug 2015 05:35 pm Go to last post
  10. Smile 'Safety First, Safety Always' Logo in AutoCad

    Hi! I'm a student that needs to make this logo in autocad. the problem is, I can't make the 'safety always' part. Please help me. Need to pass this, this week. Thanks.

    Started by aerine‎, 25th Jul 2015 04:02 pm
    • Replies: 7
    • Views: 682
    27th Jul 2015 02:04 pm Go to last post
  11. Civil drafting school project help

    Its me again with more questions. can you guys take a look at this image and tell me if am going in the right direction? am asking this assuming you guys have seen this before.

    Started by Autocadstudent‎, 2nd Apr 2011 02:34 am
    23 Pages
    1 2 3 ... 23
    • Replies: 228
    • Views: 57,772
    25th Jul 2015 11:25 pm Go to last post
  12. Smile Thank you!!!

    Thanks for all the help I finally finished the course!

    Started by ConfusedStudent‎, 19th Jul 2015 11:20 pm
    • Replies: 1
    • Views: 389
    25th Jul 2015 03:04 pm Go to last post
  13. Unhappy Doors and windows

    I have several floor plans drawn for my projects. This is probably a silly question, but I'm going to ask it anyway. I can't seem to find out. How do I draw the doors and windows on the floor plans?...

    Started by Legacy14‎, 13th Jul 2015 09:42 pm
    • Replies: 6
    • Views: 600
    14th Jul 2015 07:12 pm Go to last post
  14. P-F structural drafting project

    I want to again thank all of you who have been posting comments to help those of us struggling with P-F projects, especially ReMark and Hondatek. Your help is priceless. I have a question about...

    Started by Legacy14‎, 30th Jun 2015 07:10 pm
    • Replies: 8
    • Views: 650
    5th Jul 2015 07:21 pm Go to last post
  15. Penn Foster Civil Project, check PLATE 1

    Ok does this look right? The 80's line remark? Od confused student?

    Started by Hondatek‎, 22nd Feb 2015 08:32 pm
    4 Pages
    1 2 3 ... 4
    • Replies: 31
    • Views: 2,728
    5th Jul 2015 07:12 pm Go to last post
  16. Unhappy Color me Baffled

    Hey guys, Well when I get to the end of my rope I can always count on you guys to help me out. I am taking a 100 level cad class online and frankly the teacher is terrible, and I am not sure this...

    Started by Behemothrex‎, 30th Jun 2015 09:40 pm
    • Replies: 6
    • Views: 557
    1st Jul 2015 05:29 pm Go to last post
  17. Question Drafting projects

    I am working on my drafting projects. What is the best way to draw the lines for the floor plans? Is it okay to use the MLINE command or is there a better way to get the 6" and 4" walls? :unsure:

    Started by Legacy14‎, 18th Jun 2015 07:02 pm
    • Replies: 7
    • Views: 781
    30th Jun 2015 07:28 pm Go to last post
  18. Smile Penn-Foster -Civil Grade Report Final

    OK everyone. I have Civil results. I scored a 95 on the civil. The last 2 plates I didn't like all that much. 80 on A/C sheet metal. 100 on both Electrical and Electrical Elective. my final grade...

    Started by Hondatek‎, 9th Jun 2015 04:34 am
    • Replies: 4
    • Views: 600
    10th Jun 2015 10:30 am Go to last post
  19. Penn-Foster -HVAC plate 1 Question.

    This has to be a typo. I will post the screen shot then feel free to leave comments. I will be E-mailing Penn-Foster shortly. Thank you guy for the help. here is screen shot #1 window S is 6 foot...

    Started by Hondatek‎, 7th May 2015 01:42 am
    2 Pages
    1 2
    • Replies: 12
    • Views: 1,156
    1st Jun 2015 10:45 am Go to last post
  20. Penn-Foster -HVAC Grade Report

    I have submitted my drawings and I have received a grade of 80. witch I think its great considering the not so great instruction. Remark They sent me the correct drawing if you care to have them. now...

    Started by Hondatek‎, 30th May 2015 11:59 pm
    • Replies: 2
    • Views: 584
    31st May 2015 05:07 pm Go to last post
  21. pf oleson subdivision cannot see drawing in paper space

    Hello, i have completed the subdivision drawing in model space but cannot see it in paper space...Need help.

    Started by md2512‎, 23rd Apr 2015 06:30 pm
    • Replies: 7
    • Views: 832
    2nd May 2015 01:07 pm Go to last post
  22. How to remove files listed on Application menu

    Hi I have Autocad lt 2011, on the Application menu listing recent files used, can I remove the ones that I dont use anymore or deleted? :unsure:

    Started by Baiksu‎, 19th Sep 2012 01:58 am
    2 Pages
    1 2
    • Replies: 14
    • Views: 3,926
    18th Apr 2015 03:52 pm Go to last post
  23. Extra hatch trim

    Hy All, Friends my problem is that. . . I have to trim hatch. . . Because no need to extra hatch. . . its lot of edge inscribed in circle. . . But this is not trim. . . Plz help me. . ....

    Started by Muhammad Sadiq‎, 3rd Apr 2015 08:19 am
    • Replies: 4
    • Views: 865
    9th Apr 2015 07:20 am Go to last post
  24. ask for help

    hello guys I have to do some work to school which I must to explain working of screw. Our proffesor told uz that it can be some video or simulation animation where he will see axiom of inclined...

    Started by blazejko10‎, 21st Mar 2015 10:41 pm
    2 Pages
    1 2
    • Replies: 16
    • Views: 1,843
    31st Mar 2015 06:44 pm Go to last post
  25. Smile Block Authoring Palettes

    Hi All, I will use Block Authoring Palette, But this is not Getting in MODEL i will use 2010 version of CAD. Please Solve my problem. Advance Thanx, SADIQ.

    Started by Muhammad Sadiq‎, 6th Mar 2015 08:57 am
    • Replies: 1
    • Views: 800
    6th Mar 2015 02:48 pm Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 250 views
Hot thread with unread posts
More than 15 replies or 250 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts