Search:

Type: Posts; User: ReMark

Page 1 of 5 1 2 3 4

Search: Search took 0.44 seconds; generated 36 minute(s) ago.

  1. Replies
    21
    Views
    145

    I'm not sure why you needed to go through all...

    I'm not sure why you needed to go through all that trouble (trimming and erasing). I was able to create boundaries for probably 2/3rds of the drawing simply using the Boundary command.
  2. Replies
    3
    Views
    92

    Did you try the SURFPATCH command?

    Did you try the SURFPATCH command?
  3. Replies
    21
    Views
    145

    The 3D entities I mentioned were the ones I...

    The 3D entities I mentioned were the ones I created. If there were 3D entities in the original drawing I did not bother to look. I assumed you were unable to make picks because of inconsistencies...
  4. Replies
    21
    Views
    145

    The point of the exercise wasn't accuracy. The...

    The point of the exercise wasn't accuracy. The point was demonstrate to the OP that there was a way to ascertain the negative areas. I'll leave the accuracy to the OP since it's his drawing.
  5. Replies
    21
    Views
    145

    Red objects were created using the Boundary...

    Red objects were created using the Boundary command.

    Cyan objects were created using the 3DPolyline command.

    Yes, my drawing contains 3D objects called "solids".
  6. Replies
    21
    Views
    145

    50206 Corrected a few errors and added the final...

    50206
    Corrected a few errors and added the final piece to the puzzle.

    I'm done.
  7. Replies
    21
    Views
    145

    50205 OK...this was just for fun.

    50205
    OK...this was just for fun.
  8. Replies
    21
    Views
    145

    50204 Picked up a few extra (cyan color).

    50204
    Picked up a few extra (cyan color).
  9. Replies
    21
    Views
    145

    I just discovered another way. I'm using the...

    I just discovered another way. I'm using the 3DPolyline command.
  10. Replies
    21
    Views
    145

    50203 This is what I managed to come up with on...

    50203
    This is what I managed to come up with on my first try.
  11. Replies
    21
    Views
    145

    Would the Boundary command work? I tried and...

    Would the Boundary command work?

    I tried and had some success but it wasn't 100%.
  12. Replies
    3
    Views
    80

    What program are people using to view the...

    What program are people using to view the drawings?

    Do all these people need the ability to edit drawings?
  13. Replies
    7
    Views
    114

    It all has to do with "pixels". I wouldn't worry...

    It all has to do with "pixels". I wouldn't worry about it. Next time you'll be more careful with your picks I imagine.
  14. Replies
    7
    Views
    114

    Yes, it is and yes, I can. And it is...

    Yes, it is and yes, I can.

    And it is repeatable; I've done it three times in a row. No problem here.

    OK...I was able to reproduce your results on the fourth try. What did I do differently? I...
  15. Replies
    7
    Views
    114

    Use the Circle command with the Tan-Tan-Radius...

    Use the Circle command with the Tan-Tan-Radius option. No snapping required.

    OK. Tried it in Draftsight and Circle with the Ttr option works like a charm after which you can snap to the...
  16. Replies
    7
    Views
    114

    Did you try using an "intersection" snap point? ...

    Did you try using an "intersection" snap point? It should work.

    I opened your drawing in AutoCAD and I was able to snap to that point using "intersection". I can't test it in Draftsight at the...
  17. Replies
    9
    Views
    164

    The profile I used in shown in white in the two...

    The profile I used in shown in white in the two images seen in post #7.

    No, I did not use the Loft command the last time. I used the Extrude command.

    The width in both methods I used was based...
  18. Replies
    9
    Views
    164

    Draw the profile as though you were looking at it...

    Draw the profile as though you were looking at it from the side. You already have part of it drawn based upon what I am seeing in your last posted image.

    Another option: You can extrude the...
  19. Replies
    9
    Views
    164

    Well for one thing you left out the height. And...

    Well for one thing you left out the height. And for another we have no idea what the angle is supposed to be. I guessed at both.

    I created my version of your object by lofting a profile then...
  20. Replies
    9
    Views
    164

    I'm not sure you have provided all the necessary...

    I'm not sure you have provided all the necessary information.

    This is the best I could do with the information you provided so don't fault me for the result.

    First an isometric view.

    50181
    ...
Results 1 to 20 of 97
Page 1 of 5 1 2 3 4