Search:

Type: Posts; User: GP_

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    582

    Con un avatar così spaventi tutti, chi vuoi che...

    Con un avatar così spaventi tutti, chi vuoi che ti risponda? :D
    Look into PM
    Ciao
  2. Thread: Run another

    by GP_
    Replies
    11
    Views
    539

    Try this: ;Gian Paolo Cattaneo -...

    Try this:


    ;Gian Paolo Cattaneo - 28.Apr.2015
    (defun c:FlattenAll ()
    (if (and
    (zerop (car (getvar "viewdir")))
    (zerop (cadr (getvar "viewdir")))
    (>...
  3. Thread: Sky illumination

    by GP_
    Replies
    3
    Views
    268

    Save the sky settings in the view.

    Save the sky settings in the view.
  4. Replies
    7
    Views
    485

    Try TextToGeometry...

    Try TextToGeometry by Sean Tessier, much better than txtexp.
  5. Thread: O-ring groove

    by GP_
    Replies
    17
    Views
    1,291

    To create a profile on the cylinder you can use...

    To create a profile on the cylinder you can use this technique.
  6. Replies
    13
    Views
    796

    With "minor anomalies in his geometry" you can't...

    With "minor anomalies in his geometry" you can't use PRESSPULL. :)
  7. Replies
    13
    Views
    796

    Found some errors... 52915

    Found some errors...


    52915
  8. Replies
    27
    Views
    11,976

    Thank you Seant, works fine. :)

    Thank you Seant, works fine. :)
  9. Try this: (defun c:test ( / pt1 pt2 obj1...

    Try this:


    (defun c:test ( / pt1 pt2 obj1 ent PT3)
    (setq PT1 (getpoint))
    (setq PT2 (getpoint PT1))
    (command "_LINE" "_non" PT1 "_non" PT2 "")
    (setq obj1 (entlast))
    (setq...
  10. Replies
    45
    Views
    2,612

    Try this...

    Try this fantastic plug-in by Sean Tessier.



    52841


    notes:
    - Convert Spline to Polyline (FLATTEN)
    - Explode the polyline -> arcs
  11. Replies
    39
    Views
    2,264

    PROJECTGEOMETRY...

    PROJECTGEOMETRY ?
  12. Thread: convex or concave

    by GP_
    Replies
    8
    Views
    609

    My ~2 cents, if there aren't collinear points. :)...

    My ~2 cents, if there aren't collinear points. :)


    (defun c:test ( / lst sel R L)
    (if (setq sel (ssget "_+.:E:S" '((0 . "LWPOLYLINE") (-4 . "&=") (70 . 1))))
    (progn
    ...
  13. Thread: lisp polyline

    by GP_
    Replies
    23
    Views
    1,844

    1+ 52151 edit: oops ymg, two...

    1+

    52151



    edit: oops
    ymg, two minutes later... :)
  14. Thread: lisp polyline

    by GP_
    Replies
    23
    Views
    1,844

    (or cal (arxload "geomcal")) works on all...

    (or cal (arxload "geomcal")) works on all version, from v2013 it has become geomcal.crx
  15. Replies
    13
    Views
    1,003

    Follow the Henrique's suggestion: 52070...

    Follow the Henrique's suggestion:



    52070



    or a change of my first:
    (vl-cmdf "_solidedit" "_f" "_c" pause "" "_non" "0,0,0" "_non" "0,0,0" "_X" "_X" "_explode" "_L")
  16. Replies
    13
    Views
    1,003

    ...look into Camtasia...

    ...look into Camtasia
  17. Replies
    13
    Views
    1,003

    Try this: (vl-cmdf "_solidedit" "_f" "_c"...

    Try this:


    (vl-cmdf "_solidedit" "_f" "_c" pause "" pause pause "" "")


    52039
  18. Try: (autoload "MyLisp.LSP" "MyCommand")

    Try:

    (autoload "MyLisp.LSP" "MyCommand")
  19. This? ...

    This?

    http://www.cadtutor.net/forum/showthread.php?84126-Rapidly-rotating-three-dimensional-solid&p=576502&viewfull=1#post576502
  20. Replies
    7
    Views
    693

    Hi Henrique, in my AC2014 the OP's code works...

    Hi Henrique,

    in my AC2014 the OP's code works only with primitive solids.
Results 1 to 20 of 100
Page 1 of 5 1 2 3 4