Search:

Type: Posts; User: ReMark

Page 1 of 5 1 2 3 4

Search: Search took 0.39 seconds.

  1. Replies
    9
    Views
    267

    I too was thinking number 1 could be a light but...

    I too was thinking number 1 could be a light but it is the only one shown on a drawing that has at least six rooms.

    Strange that someone from Pakistan would reference a drawing done in imperial...
  2. I can see where you might have difficulty with...

    I can see where you might have difficulty with drawing the front view as there is a lot going on with this object. You have both a slanted back and top, the circular objects standing vertically up...
  3. Replies
    9
    Views
    267

    You realize you initially asked about symbols...

    You realize you initially asked about symbols used in a civil engineering drawing yet you post images taken from an architectural drawing?

    Numbers 7 and 8 will the user to an elevation view that...
  4. Replies
    9
    Views
    215

    I mentioned scale factors because the OP talked...

    I mentioned scale factors because the OP talked about plotting from paper space which led me to assume he was viewing the model space drawing via a viewport. For the viewport to plot correctly the...
  5. Replies
    9
    Views
    215

    This statement is false: "The default scale 1:20...

    This statement is false: "The default scale 1:20 does not show up in the imperial default scale list."

    51785

    I do all my drawings in imperial units and this scale list is the default in the...
  6. Replies
    9
    Views
    215

    The viewport scale factor for 1:20 is not the...

    The viewport scale factor for 1:20 is not the same as the scale factor for 1"=20'.
  7. It can happen if the drawing the line you are...

    It can happen if the drawing the line you are copying from was, at one time or another, edited in Microstation.

    Simple to check. Open your linetypes window. Any of them have the letters DGN...
  8. Replies
    9
    Views
    215

    Maybe I need a refresher course. In all my...

    Maybe I need a refresher course.

    In all my years doing civil engineering work I've never seen a drawing that purported to be drawn at a scale of one inch equals twenty feet designated 1:20. I've...
  9. Replies
    12
    Views
    307

    Once you group the objects they act in unison. ...

    Once you group the objects they act in unison.

    How many objects do you have?

    How many objects have to be rotated at a 90 degree angle?

    How many objects have to be rotated at a 45 degree...
  10. Maybe just work on getting the main body of the...

    Maybe just work on getting the main body of the object drawn first in all three views then go back an add the rest?

    Use the top and a side views for projecting lines that will help you create the...
  11. Replies
    9
    Views
    215

    1:20 metric is roughly equivalent to the imperial...

    1:20 metric is roughly equivalent to the imperial scale of 3/4"=1'-0". It is not the same as 1"=20'.

    Your paper space viewport needs to have its scale set to 1"=20'. If that scale hasn't...
  12. Thread: points

    by ReMark
    Replies
    3
    Views
    160

    If you open the CUI and look under Menus is...

    If you open the CUI and look under Menus is Format listed there?
  13. Replies
    2
    Views
    150

    I try to avoid the use of PDF's as much as...

    I try to avoid the use of PDF's as much as possible.
  14. Replies
    2
    Views
    163

    That is one option. The other would be to use...

    That is one option. The other would be to use the command -dwgunits and change your drawing units from millimeters to meters. You must include the dash.
  15. Replies
    33
    Views
    702

    It is dashed because it is below the surface that...

    It is dashed because it is below the surface that you can see. It would not be shown using a continuous line.
  16. Replies
    33
    Views
    702

    If the dimensions in post #1 were metric then...

    If the dimensions in post #1 were metric then 4.12 would have been written as 4,12 right?

    gokhandmr: Is this an assignment you got in class from your instructor?
  17. Replies
    11
    Views
    271

    Same technique here. I'm using Win 7 x64 as well.

    Same technique here. I'm using Win 7 x64 as well.
  18. Replies
    11
    Views
    271

    How are you setting this? I don't seem to have a...

    How are you setting this? I don't seem to have a problem with the column disappearing after closing down AutoCAD then opening it up again.
  19. Replies
    33
    Views
    702

    51743 For demonstration purposes only. The 3D...

    51743
    For demonstration purposes only. The 3D model is incomplete (no holes).

    On the left we see the two channels cut through the object (front-to-back & side-to-side).

    On the right is a...
  20. Replies
    33
    Views
    702

    51742 Your three views should look like this....

    51742
    Your three views should look like this.
    Keep in mind that the opening seen in the front view passes all the way through.
Results 1 to 20 of 96
Page 1 of 5 1 2 3 4