Ubrigens Posted May 26, 2010 Share Posted May 26, 2010 Trying to intersect 3 equi-diameter tubes at 120 degrees, Unable to find method for removing excess solids at junction. Anyone have a solution???? Quote Link to comment Share on other sites More sharing options...
Cad64 Posted May 26, 2010 Share Posted May 26, 2010 I'm not sure exactly what type of result you're looking to achieve, but try UNION or INTERSECT or INTERFERE. I'm sure one of those commands will get you what you're looking for. Quote Link to comment Share on other sites More sharing options...
JD Mather Posted May 26, 2010 Share Posted May 26, 2010 http://home.pct.edu/~jmather/content/CAD238/AutoCAD%202007%20Tutorial%208.pdf Page 4. Not the same angles you have but it can easily be done. Quote Link to comment Share on other sites More sharing options...
Ubrigens Posted May 27, 2010 Author Share Posted May 27, 2010 I'm not sure exactly what type of result you're looking to achieve, but try UNION or INTERSECT or INTERFERE. I'm sure one of those commands will get you what you're looking for. Tried these commands without any success,which was reason for request! Quote Link to comment Share on other sites More sharing options...
Ubrigens Posted May 27, 2010 Author Share Posted May 27, 2010 I'm guessing all three pipes also have the same centerline elevation. Here's another possible option. Make a copy of all three pipes off to one side. Union the three original pipes together. Use the Intersect command on the copy of the three pipes. Take the result you got from the copy, move it into position with your original pipes. Subtract what you just moved from your original (unioned) pipes. Does it work? Sorry...I cannot test it out myself (which I usually do). My friend's laptop doesn't have AutoCAD on it. I'm really supposed to be troubleshooting a Win7 (not genuine) problem for him. Shhhhhhh...don't tell him I'm here. Thanks. Sounds like it might work,but did'n't----posibble problem is that I omitted to mention that pipes are not co-planar----sorry! Quote Link to comment Share on other sites More sharing options...
Ubrigens Posted May 27, 2010 Author Share Posted May 27, 2010 http://home.pct.edu/~jmather/content/CAD238/AutoCAD%202007%20Tutorial%208.pdf Page 4. Not the same angles you have but it can easily be done. Aoutocad 2006 does not have sweep command!!! Quote Link to comment Share on other sites More sharing options...
ReMark Posted May 27, 2010 Share Posted May 27, 2010 Post the drawing and so we can take a look at what you have since your description of the problem seems to have changed. Note: I deleted my previous post because after testing it this morning (Thursday) I found it to be unworkable. Quote Link to comment Share on other sites More sharing options...
ReMark Posted May 27, 2010 Share Posted May 27, 2010 Different approach. I think it could be done using the Slice command and the Surface option. But until I see how the pipes are actually configured I can't be 100% sure. Well it can be done if all the pipes centerlines are at the same elevation. In the test I did I had three 2" diameter pipes at angles of 0, 60 and 120 degrees and one end of all three pipes met at the same location. Quote Link to comment Share on other sites More sharing options...
ReMark Posted May 27, 2010 Share Posted May 27, 2010 For your consideration. Three pipes (max angle 120 deg). I sliced the top half of the pipes off so the intersections could be viewed. Quote Link to comment Share on other sites More sharing options...
JD Mather Posted May 27, 2010 Share Posted May 27, 2010 could be done using the Slice command and the Surface option. ... Not in r2006. The parts can be done in 2006, but we need to see what the OP has completed so far. Quote Link to comment Share on other sites More sharing options...
ReMark Posted May 27, 2010 Share Posted May 27, 2010 Darn that 2006! Why doesn't it cooperate? Quote Link to comment Share on other sites More sharing options...
Cad64 Posted May 27, 2010 Share Posted May 27, 2010 Tried these commands without any success,which was reason for request! Maybe you should have mentioned that in your original post. Then I wouldn't have wasted my time offering the advice. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.