+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 22
  1. #1
    Full Member
    Using
    AutoCAD 2010
    Join Date
    Feb 2011
    Posts
    52

    Default Electrical Drafting School Project.

    Registered forum members do not see this ad.

    Car5858 i am doing the elctrical project now. i think i finished plate 1 and pl 2 is 50% i cant figure out the other half of pl 2.. Can you post the images of pl 1 and 2 to compare. this are my 2 plates. Thank you for your help.elec. pl1.jpg:elec. pl2.jpg

  2. #2
    Senior Member Car5858's Avatar
    Computer Details
    Car5858's Computer Details
    Operating System:
    Win7
    Computer:
    Gateway Sx2800-3
    CPU:
    Intel Quad Core 2.33
    RAM:
    8GB
    Graphics:
    Intel 4500
    Primary Storage:
    Seagate 500 gb
    Secondary Storage:
    Passport usb 500 gb
    Monitor:
    HANNspree 22"
    Discipline
    See details...
    Car5858's Discipline Details
    Occupation
    retired, disibality
    Discipline
    See details below.
    Details
    Tutor, AMA glider competitions.
    Using
    AutoCAD 2010
    Join Date
    May 2009
    Location
    Hammond
    Posts
    373

    Default

    That is a good start be carefull with the arragment.
    Plate 2 should look like this. Remember that everything should line up. Also it will be better if the background is black, it will reduce eye strain.

    Make blocks of the symbols, these will become the legend, then its just a matter of copy and paste, with some rotation if needed.
    Attached Images

  3. #3
    Senior Member Car5858's Avatar
    Computer Details
    Car5858's Computer Details
    Operating System:
    Win7
    Computer:
    Gateway Sx2800-3
    CPU:
    Intel Quad Core 2.33
    RAM:
    8GB
    Graphics:
    Intel 4500
    Primary Storage:
    Seagate 500 gb
    Secondary Storage:
    Passport usb 500 gb
    Monitor:
    HANNspree 22"
    Discipline
    See details...
    Car5858's Discipline Details
    Occupation
    retired, disibality
    Discipline
    See details below.
    Details
    Tutor, AMA glider competitions.
    Using
    AutoCAD 2010
    Join Date
    May 2009
    Location
    Hammond
    Posts
    373

    Default

    On plate one I think you are missing some components in the kitchen, may want to check that. Don't forget your legand.

  4. #4
    Full Member
    Using
    AutoCAD 2010
    Join Date
    Feb 2011
    Posts
    52

    Default

    Thank you car5858. i was worried about some outlets that were not connected to anything on plate one. I read the project booklet several times and did not find conections for some outlets. i will do the legand. thank you.

  5. #5
    Full Member
    Using
    AutoCAD 2010
    Join Date
    Feb 2011
    Posts
    52

    Default

    do you have the link the post that needs help with the oleson village. I want to help too.

  6. #6
    Senior Member Car5858's Avatar
    Computer Details
    Car5858's Computer Details
    Operating System:
    Win7
    Computer:
    Gateway Sx2800-3
    CPU:
    Intel Quad Core 2.33
    RAM:
    8GB
    Graphics:
    Intel 4500
    Primary Storage:
    Seagate 500 gb
    Secondary Storage:
    Passport usb 500 gb
    Monitor:
    HANNspree 22"
    Discipline
    See details...
    Car5858's Discipline Details
    Occupation
    retired, disibality
    Discipline
    See details below.
    Details
    Tutor, AMA glider competitions.
    Using
    AutoCAD 2010
    Join Date
    May 2009
    Location
    Hammond
    Posts
    373

  7. #7
    Forum Newbie
    Using
    AutoCAD 2009
    Join Date
    Aug 2011
    Posts
    8

    Default I'm wondering if the hw assignments have changed in the last year?

    I am also working on this project, did you draw the lines and layout exactly like the drawing you were provided, or did you rotate things like the resistors for the purposes of fitting every thing on one sheet?

    Quote Originally Posted by Autocadstudent View Post
    Car5858 i am doing the elctrical project now. i think i finished plate 1 and pl 2 is 50% i cant figure out the other half of pl 2.. Can you post the images of pl 1 and 2 to compare. this are my 2 plates. Thank you for your help.Attachment 27655:Attachment 27654

  8. #8
    Senior Member Car5858's Avatar
    Computer Details
    Car5858's Computer Details
    Operating System:
    Win7
    Computer:
    Gateway Sx2800-3
    CPU:
    Intel Quad Core 2.33
    RAM:
    8GB
    Graphics:
    Intel 4500
    Primary Storage:
    Seagate 500 gb
    Secondary Storage:
    Passport usb 500 gb
    Monitor:
    HANNspree 22"
    Discipline
    See details...
    Car5858's Discipline Details
    Occupation
    retired, disibality
    Discipline
    See details below.
    Details
    Tutor, AMA glider competitions.
    Using
    AutoCAD 2010
    Join Date
    May 2009
    Location
    Hammond
    Posts
    373

    Default

    britt6875

    Things may have changed, these drawings were done in 09. Refer to your instructions. Tere was one statement in mine about the sample drawings being distorted requiring you to correct them.

  9. #9
    Full Member
    Using
    AutoCAD 2010
    Join Date
    Sep 2011
    Posts
    28

    Default

    could someone please post a screenshot of electrical plate 1 for pennfoster. I have finished the floor plan and need help on how to start laying out the electrical.
    Thanks

  10. #10
    Quantum Mechanic ReMark's Avatar
    Computer Details
    ReMark's Computer Details
    Operating System:
    Windows 7 Pro 64-bit
    Computer:
    Thinkmate
    Motherboard:
    Intel DX58SO2 LGA1366 X58
    CPU:
    Intel i7-960 Quad-core 3.20GHz 8MB cache
    RAM:
    12GB (3x4GB) PC3-106000 DDR3
    Graphics:
    nVidia Quadro K4200, 4GB GDDR5
    Primary Storage:
    150GB Velocipraptor 10,000 rpm
    Secondary Storage:
    none
    Monitor:
    Dell P24LLH - 24" wide screen LCD
    Discipline
    See details...
    ReMark's Discipline Details
    Occupation
    CAD Draftsman/Designer...chemical manufacturing.
    Discipline
    See details below.
    Details
    I work for a specialty chemical manufacturer. I do a little bit of everything from P&IDs to civil to architectural and structural.
    Using
    AutoCAD 2018
    Join Date
    Nov 2005
    Location
    Norwalk, CT USofA
    Posts
    46,375

    Default

    Registered forum members do not see this ad.

    P-F Elec Plt 1.PNG
    How's this look?

    Disclaimer: I did not do the drawing. It is posted here with the permission of the author. I cannot answer specific questions about it either.
    "I have only come here seeking knowledge. Things they wouldn't teach me of in college." The Police

    Eat brains...gain more knowledge!

    I'm now a full member of the Society for the Promotion of Mediocrity in CAD. Standards? We don't need no stinkin' standards! Take whatever advice I offer and do the opposite.

Similar Threads

  1. HVAC School project
    By Autocadstudent in forum Student Project Questions
    Replies: 94
    Last Post: 18th Nov 2016, 09:45 pm
  2. Civil drafting school project help
    By Autocadstudent in forum Student Project Questions
    Replies: 232
    Last Post: 25th May 2016, 04:42 pm
  3. school CAD project
    By bdr2k5 in forum Student Project Questions
    Replies: 27
    Last Post: 25th Apr 2010, 11:44 am

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts