jimemack Posted August 29, 2012 Share Posted August 29, 2012 I am trying to make an assembly from two parts that were sketched in such a way that the orientations they were created in are not compatible, so I need to reorient one part during assembly, but can't seem to make it happen. Is this something that can be done, or does one of the parts have to be re-sketched? Both parts are in the best orientation for stand-alone use, so I really don't want to redraw either one. Thanks for any advice you can give. Jim Quote Link to comment Share on other sites More sharing options...
JD Mather Posted August 29, 2012 Share Posted August 29, 2012 Use assembly constraints. In the real world when you pick up two parts they can be oriented in any way and then you orient them as needed to assemble. SolidWorks replicates the real world. Use assembly constraints. Attach your assembly here if you can't figure it out. Quote Link to comment Share on other sites More sharing options...
jimemack Posted August 30, 2012 Author Share Posted August 30, 2012 Thanks, Can you just tell me where to go to set the constraints? I can't seem to find anything but vague information in Solidworks. I am very new to this software, so I'm a bit lost, even in the help system. I can't send the assembly because it is an invention. Thank you. Quote Link to comment Share on other sites More sharing options...
fuccaro Posted August 31, 2012 Share Posted August 31, 2012 Select the first "thing" you wish to constrain (say a point or a surface), shift+select the second thing on the second part. Right-click and choose MATE. Quote Link to comment Share on other sites More sharing options...
JD Mather Posted August 31, 2012 Share Posted August 31, 2012 Attach your assembly here if you can't figure it out. Quote Link to comment Share on other sites More sharing options...
jimemack Posted August 31, 2012 Author Share Posted August 31, 2012 I'm not explaining myself properly... I'm not trying to mate anything...yet. I'm trying to get both parts on the screen, but with one of the parts needing to be rotated to a different orientation. If I mate them, they'll both rotate, when I only want one of the to be rotated before mating them. Let me know if that's still not clear. Thanks, Jim Quote Link to comment Share on other sites More sharing options...
bhamze Posted August 31, 2012 Share Posted August 31, 2012 Try the move component command. It should be located in the assembly tab. Quote Link to comment Share on other sites More sharing options...
JD Mather Posted September 1, 2012 Share Posted September 1, 2012 I'm not trying to mate anything... Attach your assembly here. Quote Link to comment Share on other sites More sharing options...
SuperCAD Posted September 1, 2012 Share Posted September 1, 2012 (edited) If the parts are fixed or mated, you won't be able to do anything. Look at each part in the design tree. If there is a (f) in front of it, that means it is fixed and you will need to right click on the part name in the tree and select "float" before you can do anything. If there is a (-) in front of it, that means that the part is not mated (either fully or partially), and you can click on it to see if you can move it (left click) or rotate it (right click) (you may have to click on a face and not a vertex to get it to move or rotate). If there is nothing in front of the name, that means it is fully mated, and if you want to move or rotate anything you'll need to suppress or delete the mates that are constraining it. Edited September 1, 2012 by SuperCAD Clarity of steps. Quote Link to comment Share on other sites More sharing options...
jimemack Posted September 1, 2012 Author Share Posted September 1, 2012 Thanks SuperCAD, I'll try those options. JD Mather: I can't attach the assembly. As I said to you before, it's an invention. Quote Link to comment Share on other sites More sharing options...
JD Mather Posted September 2, 2012 Share Posted September 2, 2012 JD Mather: I can't attach the assembly. As I said to you before, it's an invention. It should be beyond trivially easy to create a dummy assembly that exhibits the same behavior without giving away any intellectual property. There are a lot of files already created for you in the Tutorials - you simple need to set up the problem like your actual problem so that others can see where you are getting stuck. Quote Link to comment Share on other sites More sharing options...
jimemack Posted September 2, 2012 Author Share Posted September 2, 2012 ...but I'll tell you what, JD Mather, if you attach one of your inventions, assuming you have any, I'll trade you for mine. Your help, by the way, and I'm sure a lot of folks would agree with me, is less than help. You need to actually "think" about how to help someone, rather than doing it for them...OK? Quote Link to comment Share on other sites More sharing options...
jimemack Posted September 2, 2012 Author Share Posted September 2, 2012 JD Mather: "beyond trivially easy" That is supposed to make someone feel good about themselves, right? I'm just trying to align myself with your "flavor" of help. As I see it, you think most people in the world should be at your level in order for you to expend any energy to formulate any substantive answer, correct? Just wondering, JD Mather. Quote Link to comment Share on other sites More sharing options...
jimemack Posted September 2, 2012 Author Share Posted September 2, 2012 I'll tell you what, SuperCad knows how to treat people. I have never used SolidWorks before a week or two ago, but have been designing mechanical and electronic devices since I was seven years old. I have no degree, but am highly paid - six figures - and owe my own success to others that have taken the time to answer my questions as if they were the "askers". SuperCAD is a good teacher, JD...well, JD could be. Quote Link to comment Share on other sites More sharing options...
fuccaro Posted September 3, 2012 Share Posted September 3, 2012 I'm not trying to mate anything...yet. Just a small observation: in the MATE dialg there is an obtion: use for positioning only. Using that you will get the parts in the right position, but no mate will be created. So a possible workflow: fix the first part and check is the second one is "Float", use the Mate with that positioning option checked and finaly make the first part Float again. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.