Jump to content
Blur314

User input: Getpoint OR real at the same time. Its possible?

Recommended Posts

Blur314

Hi everybody,

 

First thing I want to apologize if something that I wrote sounds strange. Im spanish and my english is not as good as it should be=P.

Im learling little by little autolisp things, mostly strugling through examples, codes, etc... many of them from this forum so I thank you a lot ^_^.

 

At this moment I'm developing a routine that breaks/trims walls in order to insert doors or windows, and, after looking for it a few days, I would like to know if there's a way to use a number that users input on the command line (in a getpoint) without getting an error.,... wich is that happends everytime =/.

 

;; HOLE-O-MaTIC 2000
;;  by Arturo Blanco Ureña. 2013
;; Breaks "walls" in order to insert windows or doors
;; Based initialy on code from Pavel Chour http://klobouk.fsv.cvut.cz/~chour/Lisp/Chapter%206.htm

(defun error1 (errmsg)
  (command "_undo" "_end")
  (setvar "CMDECHO" 1)
  (setvar "OSMODE" osmodevar)
  (setq *error* temperr)
  (prompt "\nAchtung!!! Verboten!!! Error!!!\n")
 (princ)
 )

(defun c:holes(/ );P1a P2a P1 P2 P3 P4 A1 A2)
 (setq osmodevar 	(getvar 'OSMODE)
temperr   	*error*
*error*   	error1
 	)
 (if (not ancho) (setq ancho 1.50))
 (setq Tancho (rtos ancho)
P1 "Width"
)
 (setvar "CMDECHO" 0)
 (command "_undo" "_begin")
 (setvar "osmode" 512)
 
 ;I'm using this structure in order to go back to the menu so I can change my mind several times.
 ;Don't know if there's a better way =P. 
 ;---
 (while (= P1 "Width")
  (initget 128)
  (setq P1 (getpoint (strcat "\nSelect Point or [Center/Width]<" Tancho ">:")))
  (cond ((numberp P1)	(setq ancho P1)			;trying to recognice P1 as a number but always goes on error =/
  		(setq Tancho (rtos ancho))
  );cond1
    	 ((= P1 "Width")(setvar "osmode" 35)		
  		(setq ancho (getdist "\nWidth of the Door/window?:"))
			(setq Tancho (rtos ancho))
  );cond2
   );end cond
  );end while
 ;---
 
 (cond ((= P1 "Center") (setvar "OSMODE" 518) 		;If the user want to break from the center of the window.
 		(setq P1a (getpoint (strcat "\nSelect center <" Tancho ">:")))
 		(setvar "OSMODE" 128)
		(setq P2a (getpoint P1a "\nSelect the other side of the wall:")
		      A1 (angle P1a P2a)
		      A2 (+ (* pi 1.5) A1)
		      P1 (polar P1a A2 (* ancho 0.5))
		      P3 (polar P1a A2 (* ancho -0.5))
		      P2 (polar P2a A2 (* ancho 0.5))
		      P4 (polar P2a A2 (* ancho -0.5))
		      )
 );end cond1
  (T	 (setvar "osmode" 128) 			;if he/she wants to start from one side
	 (setq P2 (getpoint P1 "\nSelect the other side of the wall:"))
	 (setvar "osmode" 512)
  	 (setq	A1 (angle P1 P2)
		A2 (+ (* pi 1.5) A1)
		P3 (polar P1 A2 ancho)
		P4 (polar P2 A2 ancho)
		P1a (polar P1 A2 (* ancho 0.5))
		P2a (polar P2 A2 (* ancho 0.5))
  		)
   );end else
);end cond
 
 (setvar "osmode" 512)
 (command	"_break" P1 P3
           	"_break" P2 P4 
   		"_line" P1 P2 "")
 (setq L1 (entlast))
 (command	"_line" P3 P4 "")
 (setq L2 (entlast))
 
 ;I add this in order to trim extra lines in the middle of the wall.
 (command "_trim" L1 L2 "" "B" P1a P2a "" "")
 
 (command "_undo" "_end")
 (setvar "CMDECHO" 1)
 (setvar "OSMODE" osmodevar)
 (setq *error* temperr)
 (princ)
);end

 

As you see You can enter the "Width" to give it, but I would like to simply write down a number when asking for a point, recognize that is a number and use it as the value of the variant. If a point is entered, then continue normally.

 

Im a bit shy and its the first time i post a code.:oops: I have used several pieces of code from others to arrange the error handling/undo and its originally based on one tutorial from Pavel Chour, so I dont know if its right that I give permission or not to use it, or even its worth it (the trim still fails and i dont really get why :ouch:) but If anyone want to use it feel free.

 

Any tips critics and opinions are welcome also :)

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...