Center mark replacement

[SLW210]

As I state in the header, I found the AutoCAD dimension "MARK" to be less than useful, so over the years I have used my own, eventually writing some LISP, as well as having found the mentioned LISP by alanjt. I really don't care for mucking around with the new CENTERMARK either.

 

Thought I might as well share it, some may find it handy.

 

;;; Replace Diameter/Radius dimension CenterMarks with two CENTER2 linetype lines.
;;;
;;; https://www.cadtutor.net/forum/topic/99350-center-mark-replacement/#findComment-680408
;;;
;;; By SLW210 (a.k.a. Steve Wilson)
;;;
;;;| Since AutoCAD in there infinite wisdom makes the default dimdia and dimrad center marks useless
     by not allowing them to be associated by other dimensions and not allowing an individual color and linetype
     I came up with this little routine. Much faster, it was using some commands, I went to removing commands.
     I used to get rid of the default the drew a centermark and copied from center to center, a bit tedious at best.

     I started with this from Alan J Thompson, so thanks to him.
    ================================================================
     Turn off the centermark for diameter and radius dimensions

     https://www.cadtutor.net/forum/topic/18792-request-routint-to-turn-off-center-mark-for-single-entity/#findComment-153451

     By alanjt|;
;;;
;;; ================================================================
;;; ================================================================
;;; CtrMrkRep.lsp
;;;
;;; Replace Diameter/Radius dimension center marks with
;;; two CENTER2 linetype lines.
;;;
;;; 
;;; AutoCAD 2018-2026 should work as well as BricsCAD and others.
;;;
;;; ================================================================
;;; ================================================================
;;; Original dimensions are retained.
;;;
;;; Replacement geometry:
;;;   Layer    : CenterMark
;;;   Color    : ByLayer
;;;   Linetype : ByLayer
;;;   Layer Color    : ACI 5 (Blue)
;;;   Layer Linetype : CENTER2
;;;
;;; Modes:
;;;   Select         - manually selected DIMDIAMETER/DIMRADIUS
;;;   Current        - all such dimensions in current Model/Layout space
;;;   All            - all such dimensions in all paperspace layouts
;;;
;;; Associated dimension center marks:
;;;   Disabled using ActiveX acCenterNone.
;;;
;;; Duplicate centers:
;;;   Only one centerline cross is created for each unique center
;;;   within each Model/Layout space.
;;; ================================================================

 

 

 

CtrMrkRep.lsp

[Paul Li]

When you mention dimension mark I assume you’re referring to AutoCADs original DIMCENTER command which I agree is quite useless. But I do think the number of commands beginning with the word center introduced back in 2017 were a lot more useful since finally the “marks” can now be made associatively to the objects selected. 

[SLW210]

I tried and tried to get the new Centermark to work nicely out of the box, too hard to get the proper size for starters and just do not care for it for a replacement for the DIMCENTER, the simple Lines work a lot better and allow you to snap associative dimensions so if something changes the center to center and center to end remain correct.

 

 

[pkenewell]

Have you tried: https://www.lee-mac.com/associativecenterlines.html ?

[SLW210]

1 hour ago, pkenewell said:

Have you tried: https://www.lee-mac.com/associativecenterlines.html ?

I know of that one, but my LISP replaces the centermarks for dimdiameter and dimradius, by selection, by current or all.

 

I could possibly add reactors to mine, not sure it's necessary.

[pkenewell]

21 minutes ago, SLW210 said:

I know of that one, but my LISP replaces the centermarks for dimdiameter and dimradius, by selection, by current or all.

 

I could possibly add reactors to mine, not sure it's necessary.

 

Sure, I know what you mean. I have my own routine i spun years ago that i still use. i use a linetype scale ratio to keep the center with a single set of gaps and centermark. Although it's not perfect, it's good enough for me.